Although there is no standard size for a chest of drawers, the most common size is 38 inches wide. A chest of drawers this size is small enough to fit in most bedrooms, but large enough to have ample storage space.
The standard dresser measures between 30 to 50 inches in height, 30 to 70 inches across, and 18 to 24 inches deep. Aside from providing substantial space for storing clothes, a standard dresser offers plenty of space for display.
A standard dresser has between six and nine drawers, is around waist tall (26″ – 44″), is 36″ – 60″ wide, and is 16″ – 20″ deep. However, these can vary and you should choose an option that works best in your bedroom.
How do I know my dresser size?
When you measure a dresser, you should measure its height, length, and width. Measure the height from the floor to the tallest point of the dresser. The width of the dresser is how far forward it reaches from the wall, so you will measure from the back of the dresser to the front.
How long is the average dresser?
The typical, rectangular dresser usually measures about 60 inches wide, 20 inches deep, and 30 inches tall. However, dresser dimensions vary quite a bit. Because waist-high can be a big difference between different people, dresser height can range from as low as 26 inches all the way up to 44 inches tall.
Do drawers come in standard sizes?
You can expect to find 5 inch or 7-inch-high drawers in 18-inch, 24-inch and 30-inch widths with a 14-inch depth.
How are drawers measured?
Begin by measuring along the bottom floor of the drawer at the back edge, middle, and front edge. Check for variations across the height of the drawer as well. Take the smallest of these measurements. Repeat this step for the depth measurement on the left edge, middle, and right edge across the floor and the height.
What is the average size of a nightstand?
Nightstand sizes depend on the space of a bedroom and the size of the bed frame. Standard nightstands are typically 21″ – 29″ wide and pair well with queen- or full-sized beds.
What is a good depth for dresser drawers?
The depth of any dresser is approximately 16 to 22 inches. The greater depth provides more stability needed in taller chests or dressers with mirrors attached to them. Drawers pull out 10 to 12 inches for use, so add that measurement to the depth when planning where to place your dresser.
How do you determine drawer size?
Measure from the back of the drawer-front to the end of the drawer box. Only measure the box, do not include the drawer front. Round the measurement off to the lower number on the tape. For example, when the measurement is 22 1/2 inches, you need to purchase 22-inch drawer slides.
How wide can drawers be?
The rule of thumb is 1.5 times the length of the drawer slide. If you have a standard depth kitchen cabinet then the normal length of drawer slide is 22”. If you multiply 22” x 1.5 = 33”. You can go wider, but the wider you go the more chance that the slide will not pull out as smoothly as you hope or expect.
How do I choose a drawer slide size?
Measure the box, not the drawer front
Start at the back of the box and measure to the front of the box without including the face of the drawer. Once you have the length, round the number down. For example, if the drawer is 20 ½ inches long you will need to purchase 20 inch drawer slides.
Can drawer slides be shorter than drawer?
You should always use the longest slide possible for your application, without exceeding the drawer depth into the cabinet. The Height of a Drawer Slide is usually only a limiting factor, in the sense that you can’t install a slide that is taller than your drawer or pull-out.
How big are drawer boxes?
Allow at least 1/4” of clearance above and below the drawer, giving you a height of 5-1/2” (6” minus 1/4” at top and 1/4” at bottom). Your drawer box should be 17” wide, 5-1/2” tall and 22” deep.
